ОШИБКА!!! Thread already running, dropping this packet

aksel · Сб дек 29, 2007 1:30 am

Вобщем при конекте с винды mpd4 грит следующее:

mpd: PPTP connection from 192.168.0.222:1310
pptp0: attached to connection with 192.168.0.222:1310
[client0] IFACE: Open event
[client0] IPCP: Open event
[client0] IPCP: state change Initial --> Starting
[client0] IPCP: LayerStart
[client0] IPCP: Open event
[client0] bundle: OPEN event in state CLOSED
[client0] opening link "client0"...
[client0] link: OPEN event
[client0] LCP: Open event
[client0] LCP: state change Initial --> Starting
[client0] LCP: LayerStart
[client0] device: OPEN event in state DOWN
[client0] attaching to peer's outgoing call
[client0] device is now in state OPENING
[client0] device: UP event in state OPENING
[client0] device is now in state UP
[client0] link: UP event
[client0] link: origination is remote
[client0] LCP: Up event
[client0] LCP: state change Starting --> Req-Sent
[client0] LCP: phase shift DEAD --> ESTABLISH
[client0] LCP: SendConfigReq #1
 ACFCOMP
 PROTOCOMP
 MRU 1500
 MAGICNUM b3840d12
 AUTHPROTO CHAP MSOFTv2
 MP MRRU 1600
 MP SHORTSEQ
 ENDPOINTDISC [802.1] 00 14 d1 31 77 58
pptp0-0: ignoring SetLinkInfo
[client0] LCP: rec'd Configure Request #0 link 0 (Req-Sent)
 MRU 1400
 MAGICNUM 48807ef4
 PROTOCOMP
 ACFCOMP
 CALLBACK
   Not supported
[client0] LCP: SendConfigRej #0
 CALLBACK
[client0] LCP: rec'd Configure Request #1 link 0 (Req-Sent)
 MRU 1400
 MAGICNUM 48807ef4
 PROTOCOMP
 ACFCOMP
[client0] LCP: SendConfigAck #1
 MRU 1400
 MAGICNUM 48807ef4
 PROTOCOMP
 ACFCOMP
[client0] LCP: state change Req-Sent --> Ack-Sent
[client0] LCP: SendConfigReq #2
 ACFCOMP
 PROTOCOMP
 MRU 1500
 MAGICNUM b3840d12
 AUTHPROTO CHAP MSOFTv2
 MP MRRU 1600
 MP SHORTSEQ
 ENDPOINTDISC [802.1] 00 14 d1 31 77 58
[client0] LCP: rec'd Configure Reject #2 link 0 (Ack-Sent)
 MP MRRU 1600
 MP SHORTSEQ
 ENDPOINTDISC [802.1] 00 14 d1 31 77 58
[client0] LCP: SendConfigReq #3
 ACFCOMP
 PROTOCOMP
 MRU 1500
 MAGICNUM b3840d12
 AUTHPROTO CHAP MSOFTv2
pptp0-0: ignoring SetLinkInfo
[client0] LCP: rec'd Configure Ack #3 link 0 (Ack-Sent)
 ACFCOMP
 PROTOCOMP
 MRU 1500
 MAGICNUM b3840d12
 AUTHPROTO CHAP MSOFTv2
[client0] LCP: state change Ack-Sent --> Opened
[client0] LCP: phase shift ESTABLISH --> AUTHENTICATE
[client0] LCP: auth: peer wants nothing, I want CHAP
[client0] CHAP: sending CHALLENGE len:17
[client0] LCP: LayerUp
[client0] LCP: rec'd Ident #2 link 0 (Opened)
 MESG: MSRASV5.10
[client0] LCP: rec'd Ident #3 link 0 (Opened)
 MESG: MSRAS-0-RED02
[client0] CHAP: rec'd RESPONSE #1
 Name: "tst"
[client0] AUTH: Auth-Thread started
[client0] AUTH: Trying RADIUS
[client0] RADIUS: using /etc/radius.conf
[client0] RADIUS: Adding Message Authenticator
[client0] RADIUS: RadiusPutAuth: RADIUS_CHAP (MSOFTv2) peer name: tst
[client0] AUTH: Thread already running, dropping this packet
[client0] AUTH: Thread already running, dropping this packet
[client0] AUTH: Thread already running, dropping this packet
[client0] AUTH: Thread already running, dropping this packet
[client0] RADIUS: rec'd rad_send_request failed No valid RADIUS responses received
[client0] AUTH: RADIUS returned undefined
[client0] AUTH: Trying secret file: mpd.secret
 Peer name: "tst"

Т.Е вот тут

Код: Выделить всё

[client0] AUTH: Trying RADIUS
[client0] RADIUS: using /etc/radius.conf
[client0] RADIUS: Adding Message Authenticator
[client0] RADIUS: RadiusPutAuth: RADIUS_CHAP (MSOFTv2) peer name: tst
[client0] AUTH: Thread already running, dropping this packet
[client0] AUTH: Thread already running, dropping this packet
[client0] AUTH: Thread already running, dropping this packet
[client0] AUTH: Thread already running, dropping this packet
[client0] RADIUS: rec'd rad_send_request failed No valid RADIUS responses received
[client0] AUTH: RADIUS returned undefined
[client0] AUTH: Trying secret file: mpd.secret

mpd4 пытается пробиться к радиусу но почему то не получается что может быть???

Еще при старте Mpd4 грит такую ерунду:

Код: Выделить всё

[l2tp0] ppp node is "mpd2226-l2tp0"
[l2tp0] device type "l2tp" unknown
[l2tp0] using interface ng8
set l2tp: unknown command. Try "help".
set l2tp: unknown command. Try "help".
set l2tp: unknown command. Try "help".
mpd: warning: line too long, truncated
[l2tp1] ppp node is "mpd2226-l2tp1"
[l2tp1] device type "l2tp" unknown
mpd: warning: line too long, truncated
[l2tp1] using interface ng9
set l2tp: unknown command. Try "help".
set l2tp: unknown command. Try "help".
set l2tp: unknown command. Try "help".

Опции ядра:

Код: Выделить всё

options NETGRAPH
options NETGRAPH_PPPOE
options NETGRAPH_ASYNC
options NETGRAPH_BPF
options NETGRAPH_ECHO
options NETGRAPH_ETHER
options NETGRAPH_HOLE
options NETGRAPH_IFACE
options NETGRAPH_KSOCKET
options NETGRAPH_L2TP
options NETGRAPH_LMI
options NETGRAPH_MPPC_ENCRYPTION
options NETGRAPH_ONE2MANY
options NETGRAPH_PPP
options NETGRAPH_PPTPGRE
options NETGRAPH_RFC1490
options NETGRAPH_SOCKET
options NETGRAPH_TEE
options NETGRAPH_TTY
options NETGRAPH_UI
options NETGRAPH_VJC

options IPFIREWALL
options IPFIREWALL_FORWARD
options IPFIREWALL_VERBOSE
options IPDIVERT

Винда естественно грит что такие имена и пароли не используются в данном домене бла бла бла ........
Что может быть ?????

aksel · Пт янв 11, 2008 8:45 am

Фсе. Разобрался.
Почему то в client.conf вместо

Код: Выделить всё

127.0.0.1
надо было указать 
192.168.0.1

и nas и radius у меня на одной машине странно как то .........