Проблемы с Abills 0.37

[colortv]

1)перешел на abills 0.37 и начались проблемы : не могу создать тарифный план -- выдает ошибку Error ID = 0.Дальше не двигаюсь.Хотя если просто добавить пользователя то выдает :
radtest slava 123456789 127.0.0.1:1812 0 radsecret 0 127.0.0.1
Sending Access-Request of id 119 to 127.0.0.1 port 1812
User-Name = "slava"
User-Password = "123456789"
NAS-IP-Address = 127.0.0.1
NAS-Port = 0
Framed-Protocol = PPP
rad_recv: Access-Reject packet from host 127.0.0.1:1812, id=119, length=39
Reply-Message = "Service not allow"
Но пользователь активирован!!!

[colortv]

radiusd -x:
--- Walking the entire request list ---
Waking up in 1 seconds...
rad_recv: Access-Request packet from host 127.0.0.1:34431, id=119, length=63
User-Name = "slava"
User-Password = "123456789"
NAS-IP-Address = 127.0.0.1
NAS-Port = 0
Framed-Protocol = PPP
Processing the authorize section of radiusd.conf
modcall: entering group authorize for request 1
radius_xlat: '/usr/abills/libexec/rauth.pl pre_auth'
Exec-Program: /usr/abills/libexec/rauth.pl pre_auth
Exec-Program output: Auth-Type := Accept
Exec-Program-Wait: value-pairs: Auth-Type := Accept
Exec-Program: returned: 0
modcall[authorize]: module "pre_auth" returns ok for request 1
modcall[authorize]: module "preprocess" returns ok for request 1
modcall[authorize]: module "mschap" returns noop for request 1
rlm_realm: No '@' in User-Name = "slava", looking up realm NULL
rlm_realm: No such realm "NULL"
modcall[authorize]: module "suffix" returns noop for request 1
users: Matched entry DEFAULT at line 215
modcall[authorize]: module "files" returns ok for request 1
modcall: leaving group authorize (returns ok) for request 1
rad_check_password: Found Auth-Type Accept
rad_check_password: Auth-Type = Accept, accepting the user
radius_xlat: '/usr/abills/libexec/rauth.pl'
Exec-Program: /usr/abills/libexec/rauth.pl
Exec-Program output: Reply-Message = "Service not allow"
Exec-Program-Wait: value-pairs: Reply-Message = "Service not allow"
Exec-Program: returned: 1
Found Post-Auth-Type
Processing the post-auth section of radiusd.conf
modcall: entering group REJECT for request 1
radius_xlat: '/usr/abills/libexec/rauth.pl post_auth'
Exec-Program: /usr/abills/libexec/rauth.pl post_auth
Exec-Program output:
Exec-Program: returned: 0
modcall[post-auth]: module "post_auth" returns ok for request 1
modcall: leaving group REJECT (returns ok) for request 1
Delaying request 1 for 1 seconds
Finished request 1
Going to the next request
Waking up in 1 seconds...
--- Walking the entire request list ---
Sending Access-Reject of id 59 to 127.0.0.1 port 34430
Sending Access-Reject of id 119 to 127.0.0.1 port 34431
Reply-Message = "Service not allow"
Waking up in 4 seconds...
--- Walking the entire request list ---
Cleaning up request 0 ID 59 with timestamp 47302d6d
Cleaning up request 1 ID 119 with timestamp 47302d6d
Nothing to do. Sleeping until we see a request.

[colortv]

со всем разобрался!ложная тревога!!

[smilethebest]

поделитесь плиз как решили то проблему?

[ran]

Exec-Program: /usr/abills/libexec/rauth.pl
Exec-Program output: Reply-Message = "Service not allow"

/ Клиенты/ Логины/ Информация/ Сервисы/ Internet/Статус: ?
/ Клиенты/ Логины/ Информация/ Сервер доступа/ ?