Есть связка фрирадиус 2.14 и мпд 5.3(pppoe). Сконфигурировано по мануалу на главном сайте.
Столкнулся с проблемой, а именно адрес из пула прописаного в абиллсе в упор не выдается клиенту, вместо этого - из пула мпд. Просмотрел похожие темы, но толком ничего не ясно. При коннекте в логах
Код: Выделить всё
rad_recv: Access-Request packet from host 127.0.0.1 port 62778, id=24, length=179
NAS-Identifier = "local"
Acct-Session-Id = "9663578-L-1"
NAS-Port = 1
NAS-Port-Type = Ethernet
Service-Type = Framed-User
Framed-Protocol = PPP
Calling-Station-Id = "00022db82317"
NAS-Port-Id = "xl0"
Vendor-12341-Attr-12 = 0x4c2d31
Tunnel-Medium-Type:0 = IEEE-802
Tunnel-Client-Endpoint:0 = "00:02:2d:b8:23:17"
User-Name = "test"
CHAP-Challenge = 0xbb1e68f0309325889990a470ecf88177f9747fc006
CHAP-Password = 0x0140d8180594677cfb21aaffac34721d98
+- entering group authorize {...}
++[preprocess] returns ok
Exec-Program output: Auth-Type := Accept
Exec-Program-Wait: value-pairs: Auth-Type := Accept
Exec-Program: returned: 0
++[abills_preauth] returns ok
++[mschap] returns noop
[files] users: Matched entry DEFAULT at line 172
++[files] returns ok
Exec-Program output: Session-Timeout = 1472422, mpd-limit + = "out#2=all rate-limit 64000 8000 16000", Framed-IP-Address = 10.10.10.5, Framed-IP-Netmask = 255.255.255.255,
Exec-Program-Wait: plaintext: Session-Timeout = 1472422, mpd-limit + = "out#2=all rate-limit 64000 8000 16000", Framed-IP-Address = 10.10.10.5, Framed-IP-Netmask = 255.255.255.255,
Exec-Program: returned: 0
++[abills_auth] returns ok
Found Auth-Type = Accept
Auth-Type = Accept, accepting the user
Sending Access-Accept of id 24 to 127.0.0.1 port 62778
Framed-Protocol = PPP
Framed-Compression = Van-Jacobson-TCP-IP
Finished request 1.
Going to the next request
Waking up in 4.9 seconds.
rad_recv: Accounting-Request packet from host 127.0.0.1 port 61691, id=79, length=208
NAS-Identifier = "local"
Acct-Session-Id = "9663578-L-1"
NAS-Port = 1
NAS-Port-Type = Ethernet
Service-Type = Framed-User
Framed-Protocol = PPP
Calling-Station-Id = "00022db82317"
NAS-Port-Id = "xl0"
Vendor-12341-Attr-12 = 0x4c2d31
Tunnel-Medium-Type:0 = IEEE-802
Tunnel-Client-Endpoint:0 = "00:02:2d:b8:23:17"
Acct-Status-Type = Start
Framed-IP-Address = 10.10.10.2
User-Name = "test"
Acct-Multi-Session-Id = "9663578-B-1"
Vendor-12341-Attr-13 = 0x422d31
Vendor-12341-Attr-14 = 0x6e6730
Vendor-12341-Attr-15 = 0x00000006
Acct-Link-Count = 1
Acct-Authentic = RADIUS
+- entering group preacct {...}
++[preprocess] returns ok
Exec-Program output:
Exec-Program: returned: 0
++[abills_acc] returns ok
+- entering group accounting {...}
++[unix] returns ok
[radutmp] expand: /var/log/radutmp -> /var/log/radutmp
[radutmp] expand: %{User-Name} -> test
++[radutmp] returns ok
Sending Accounting-Response of id 79 to 127.0.0.1 port 61691
Finished request 2.
Cleaning up request 2 ID 79 with timestamp +17
Может посоветуете куда смотреть?
Немного темой ошибся, переместите ежели не трудно.