, может быть дело в патчах я ставил http://abills.asmodeus.com.ua/current/m ... PD3.18.tgz на 6.2-STABLEsu-2.05b# mpd -c 10001
Multi-link PPP for FreeBSD, by Archie L. Cobbs.
Based on iij-ppp, by Toshiharu OHNO.
mpd: pid 73285, version 3.18 (root@klyacha.freelan 00:49 4-May-2007)
mpd: telnet console address is 0.0.0.0:10001
[pptp0] ppp node is "mpd-pptp0"
[pptp0] using interface ng0
mpd: local IP address for PPTP is 192.168.100.1
[pptp1] ppp node is "mpd-pptp1"
[pptp1] using interface ng1
[pptp2] ppp node is "mpd-pptp2"
[pptp2] using interface ng2
[pptp2:pptp2] mpd: PPTP connection from 192.168.100.2:3774
pptp0: attached to connection with 192.168.100.2:3774
[pptp0] IFACE: Open event
[pptp0] IPCP: Open event
[pptp0] IPCP: state change Initial --> Starting
[pptp0] IPCP: LayerStart
[pptp0] IPCP: Open event
[pptp0] bundle: OPEN event in state CLOSED
[pptp0] opening link "pptp0"...
[pptp0] link: OPEN event
[pptp0] LCP: Open event
[pptp0] LCP: state change Initial --> Starting
[pptp0] LCP: LayerStart
[pptp0] device: OPEN event in state DOWN
[pptp0] attaching to peer's outgoing call
[pptp0] device is now in state OPENING
[pptp0] device: UP event in state OPENING
[pptp0] device is now in state UP
[pptp0] link: UP event
[pptp0] link: origination is remote
[pptp0] LCP: Up event
[pptp0] LCP: state change Starting --> Req-Sent
[pptp0] LCP: phase shift DEAD --> ESTABLISH
[pptp0] LCP: SendConfigReq #1
ACFCOMP
PROTOCOMP
MRU 1500
MAGICNUM 9e736db9
AUTHPROTO CHAP MSOFTv2
pptp0-0: ignoring SetLinkInfo
[pptp0] LCP: rec'd Configure Request #0 link 0 (Req-Sent)
MRU 1400
MAGICNUM 29fd2b14
PROTOCOMP
ACFCOMP
CALLBACK
Not supported
[pptp0] LCP: SendConfigRej #0
CALLBACK
[pptp0] LCP: rec'd Configure Request #1 link 0 (Req-Sent)
MRU 1400
MAGICNUM 29fd2b14
PROTOCOMP
ACFCOMP
[pptp0] LCP: SendConfigAck #1
MRU 1400
MAGICNUM 29fd2b14
PROTOCOMP
ACFCOMP
[pptp0] LCP: state change Req-Sent --> Ack-Sent
[pptp0] LCP: SendConfigReq #2
ACFCOMP
PROTOCOMP
MRU 1500
MAGICNUM 9e736db9
AUTHPROTO CHAP MSOFTv2
[pptp0] LCP: rec'd Configure Ack #2 link 0 (Ack-Sent)
ACFCOMP
PROTOCOMP
MRU 1500
MAGICNUM 9e736db9
AUTHPROTO CHAP MSOFTv2
[pptp0] LCP: state change Ack-Sent --> Opened
[pptp0] LCP: phase shift ESTABLISH --> AUTHENTICATE
[pptp0] LCP: auth: peer wants nothing, I want CHAP
[pptp0] CHAP: sending CHALLENGE
[pptp0] LCP: LayerUp
pptp0-0: ignoring SetLinkInfo
[pptp0] LCP: rec'd Ident #2 link 0 (Opened)
MESG: MSRASV5.10
[pptp0] LCP: rec'd Ident #3 link 0 (Opened)
MESG: MSRAS-1-SHMIT
[pptp0] CHAP: rec'd RESPONSE #1
Name: "test"
[pptp0] RADIUS: using /etc/radius.conf
[pptp0] RADIUS: RadiusPutAuth: RADIUS_CHAP (MSOFTv2) peer name: test
[pptp0] RADIUS: RadiusSendRequest: RAD_ACCESS_ACCEPT for user test
[pptp0] RADIUS: RadiusGetParams: RAD_SESSION_TIMEOUT: 2349858
[pptp0] RADIUS: RadiusGetParams: RAD_EXPPP_TRAFFIC_LIMIT: 2147483648
[pptp0] RADIUS: RadiusGetParams: RAD_MICROSOFT_MS_MPPE_ENCRYPTION_TYPES: 6 (40 128 bit)
[pptp0] RADIUS: RadiusGetParams: Dropping EXPPP vendor specific attribute: 8
[pptp0] RADIUS: RadiusGetParams: RAD_FRAMED_IP_ADDRESS: 172.31.1.26
[pptp0] RADIUS: RadiusGetParams: RAD_FRAMED_IP_NETMASK: 255.255.255.255
[pptp0] RADIUS: RadiusGetParams: RAD_MICROSOFT_MS_CHAP2_SUCCESS: S=D5036B51411781F27AF5848E9F910E81B150CB0A
[pptp0] RADIUS: RadiusGetParams: Dropping EXPPP vendor specific attribute: 26
[pptp0] RADIUS: RadiusGetParams: RAD_MICROSOFT_MS_MPPE_ENCRYPTION_POLICY: 1 (Allowed)
[pptp0] RADIUS: RadiusGetParams: Dropping EXPPP vendor specific attribute: 7
[pptp0] RADIUS: RadiusGetParams: Dropping EXPPP vendor specific attribute: 5
[pptp0] RADIUS: RadiusGetParams: WARNING no MPPE-Keys received, MPPE will not work
[pptp0] RADIUS: RadiusSetAuth: Trying to use IP-address from radius-server
[pptp0] RADIUS: RadiusSetAuth: using this IP: 172.31.1.26
Response is valid
[pptp0] CHAP: sending SUCCESS
[pptp0] LCP: authorization successful
[pptp0] LCP: phase shift AUTHENTICATE --> NETWORK
[pptp0] setting interface ng0 MTU to 1400 bytes
[pptp0] up: 1 link, total bandwidth 64000 bps
[pptp0] IPCP: Up event
[pptp0] IPCP: state change Starting --> Req-Sent
[pptp0] IPCP: SendConfigReq #1
IPADDR 192.168.168.1
COMPPROTO VJCOMP, 16 comp. channels, no comp-cid
[pptp0] error writing len 20 frame to bypass: Network is down
[pptp0] CCP: Open event
[pptp0] CCP: state change Initial --> Starting
[pptp0] CCP: LayerStart
[pptp0] CCP: Up event
[pptp0] CCP: state change Starting --> Req-Sent
[pptp0] CCP: SendConfigReq #1
[pptp0] CCP: Checking whether 40 bits are enabled -> yes (RADIUS)
[pptp0] CCP: Checking whether 56 bits are enabled -> no (RADIUS)
[pptp0] CCP: Checking whether 128 bits are enabled -> yes (RADIUS)
MPPC
0x01000060: MPPE, 40 bit, 128 bit, stateless
[pptp0] error writing len 14 frame to bypass: Network is down
[pptp0] RADIUS: RadiusAccount for: test
[pptp0] RADIUS: using /etc/radius.conf
[pptp0] RADIUS: RadiusAccount: Sending accounting data (Type: 1)
[pptp0] RADIUS: RadiusSendRequest: RAD_ACCOUNTING_RESPONSE for user test
[pptp0] CCP: rec'd Configure Request #4 link 0 (Req-Sent)
MPPC
0x01000001: MPPC
[pptp0] CCP: Checking whether 40 bits are enabled -> yes (RADIUS)
[pptp0] CCP: Checking whether 56 bits are enabled -> no (RADIUS)
[pptp0] CCP: Checking whether 128 bits are enabled -> yes (RADIUS)
[pptp0] CCP: SendConfigNak #4
MPPC
0x01000060: MPPE, 40 bit, 128 bit, stateless
[pptp0] IPCP: rec'd Configure Request #5 link 0 (Req-Sent)
IPADDR 0.0.0.0
NAKing with 172.31.1.26
PRIDNS 0.0.0.0
NAKing with 192.168.168.1
PRINBNS 0.0.0.0
SECDNS 0.0.0.0
NAKing with 192.168.168.2
SECNBNS 0.0.0.0
[pptp0] IPCP: SendConfigRej #5
PRINBNS 0.0.0.0
SECNBNS 0.0.0.0
[pptp0] CCP: rec'd Configure Request #6 link 0 (Req-Sent)
MPPC
0x01000040: MPPE, 128 bit, stateless
[pptp0] CCP: Checking whether 128 bits are acceptable -> yes (RADIUS)
[pptp0] CCP: SendConfigAck #6
MPPC
0x01000040: MPPE, 128 bit, stateless
[pptp0] CCP: state change Req-Sent --> Ack-Sent
[pptp0] IPCP: rec'd Configure Request #7 link 0 (Req-Sent)
IPADDR 0.0.0.0
NAKing with 172.31.1.26
PRIDNS 0.0.0.0
NAKing with 192.168.168.1
SECDNS 0.0.0.0
NAKing with 192.168.168.2
[pptp0] IPCP: SendConfigNak #7
IPADDR 172.31.1.26
PRIDNS 192.168.168.1
SECDNS 192.168.168.2
[pptp0] IPCP: rec'd Configure Request #8 link 0 (Req-Sent)
IPADDR 172.31.1.26
172.31.1.26 is OK
PRIDNS 192.168.168.1
SECDNS 192.168.168.2
[pptp0] IPCP: SendConfigAck #8
IPADDR 172.31.1.26
PRIDNS 192.168.168.1
SECDNS 192.168.168.2
[pptp0] IPCP: state change Req-Sent --> Ack-Sent
[pptp0] IPCP: SendConfigReq #2
IPADDR 192.168.168.1
COMPPROTO VJCOMP, 16 comp. channels, no comp-cid
[pptp0] CCP: SendConfigReq #2
[pptp0] CCP: Checking whether 40 bits are enabled -> yes (RADIUS)
[pptp0] CCP: Checking whether 56 bits are enabled -> no (RADIUS)
[pptp0] CCP: Checking whether 128 bits are enabled -> yes (RADIUS)
MPPC
0x01000060: MPPE, 40 bit, 128 bit, stateless
[pptp0] IPCP: rec'd Configure Reject #2 link 0 (Ack-Sent)
COMPPROTO VJCOMP, 16 comp. channels, no comp-cid
[pptp0] IPCP: SendConfigReq #3
IPADDR 192.168.168.1
[pptp0] CCP: rec'd Configure Nak #2 link 0 (Ack-Sent)
MPPC
0x01000040: MPPE, 128 bit, stateless
[pptp0] CCP: SendConfigReq #3
[pptp0] CCP: Checking whether 40 bits are enabled -> no (RADIUS)
[pptp0] CCP: Checking whether 56 bits are enabled -> no (RADIUS)
[pptp0] CCP: Checking whether 128 bits are enabled -> yes (RADIUS)
MPPC
0x01000040: MPPE, 128 bit, stateless
[pptp0] IPCP: rec'd Configure Ack #3 link 0 (Ack-Sent)
IPADDR 192.168.168.1
[pptp0] IPCP: state change Ack-Sent --> Opened
[pptp0] IPCP: LayerUp
192.168.168.1 -> 172.31.1.26
[pptp0] IFACE: Up event
[pptp0] IFACE: using RADIUS session-timeout: 2349858 seconds
[pptp0] IFACE: using RADIUS idle-timeout: 0 seconds
[pptp0] setting interface ng0 MTU to 1396 bytes
[pptp0] exec: /sbin/ifconfig ng0 192.168.168.1 172.31.1.26 netmask 0xffffffff -link0
[pptp0] exec: /sbin/route add 192.168.168.1 -iface lo0
[pptp0] IFACE: using 0 RADIUS routes
[pptp0] exec: /usr/local/abills/libexec/linkupdown mpd up ng0 inet 192.168.168.1 172.31.1.26 test
[pptp0] IFACE: Up event
[pptp0] IFACE: using RADIUS session-timeout: 2349858 seconds
[pptp0] IFACE: using RADIUS idle-timeout: 0 seconds
[pptp0] session timeout
[pptp0] closing link "pptp0"...
[pptp0] rec'd unexpected protocol IP on link 0
[pptp0] link: CLOSE event
[pptp0] LCP: Close event
[pptp0] LCP: state change Opened --> Closing
[pptp0] LCP: phase shift NETWORK --> TERMINATE
[pptp0] RADIUS: RadiusAccount for: test
[pptp0] RADIUS: using /etc/radius.conf
[pptp0] RADIUS: Termination cause: Session timeout:, RADIUS: 5
[pptp0] RADIUS: RadiusAccount: Sending accounting data (Type: 2)
[pptp0] RADIUS: RadiusSendRequest: RAD_ACCOUNTING_RESPONSE for user test
[pptp0] setting interface ng0 MTU to 1500 bytes
[pptp0] up: 0 links, total bandwidth 9600 bps
[pptp0] RADIUS: Down Event
[pptp0] IPCP: Down event
[pptp0] IPCP: state change Opened --> Starting
[pptp0] IPCP: LayerDown
[pptp0] IFACE: Down event
[pptp0] exec: /usr/local/abills/libexec/linkupdown mpd down ng0 inet test
[pptp0] exec: /sbin/route delete 192.168.168.1 -iface lo0
[pptp0] exec: /sbin/ifconfig ng0 down delete -link0
[pptp0] CCP: Down event
[pptp0] CCP: state change Ack-Sent --> Starting
[pptp0] CCP: Close event
[pptp0] CCP: state change Starting --> Initial
[pptp0] CCP: LayerFinish
[pptp0] LCP: SendTerminateReq #3
[pptp0] LCP: LayerDown
[pptp0] rec'd proto IP during terminate phase
[pptp0] rec'd proto CCP during terminate phase
[pptp0] rec'd proto COMPD during terminate phase
[pptp0] rec'd proto COMPD during terminate phase
[pptp0] rec'd proto COMPD during terminate phase
pptp0-0: ignoring SetLinkInfo
[pptp0] LCP: rec'd Terminate Ack #3 link 0 (Closing)
[pptp0] LCP: state change Closing --> Closed
[pptp0] LCP: phase shift TERMINATE --> ESTABLISH
[pptp0] LCP: LayerFinish
[pptp0] device: CLOSE event in state UP
pptp0-0: clearing call
pptp0-0: killing channel
[pptp0] PPTP call terminated
[pptp0] IFACE: Close event
[pptp0] IPCP: Close event
[pptp0] IPCP: state change Starting --> Initial
[pptp0] IPCP: LayerFinish
[pptp0] IFACE: Close event
pptp0: closing connection with 192.168.100.2:3774
[pptp0] IFACE: Close event
[pptp0] device is now in state CLOSING
[pptp0] bundle: CLOSE event in state OPENED
[pptp0] device: DOWN event in state CLOSING
[pptp0] device is now in state DOWN
[pptp0] link: DOWN event
[pptp0] LCP: Down event
[pptp0] LCP: state change Closed --> Initial
[pptp0] LCP: phase shift ESTABLISH --> DEAD
[pptp0] device: DOWN event in state DOWN
[pptp0] device is now in state DOWN
pptp0: killing connection with 192.168.100.2:3774
[pptp0] link: DOWN event
[pptp0] LCP: Down event
