После последнего обновление в логах микротика пишет что клиенту выдается ip 0.0.0.0, хотя если посмотреть пакет радиуса в нем все в пордяке, ip-адрас выдается с пула.
куда рыть?
после обновления клиенту выдает 0.0.0.0
-
- Site Admin
- Сообщения: 5746
- Зарегистрирован: Пт янв 28, 2005 3:11 pm
- Контактная информация:
Re: после обновления клиенту выдает 0.0.0.0
radiusd -X
Re: после обновления клиенту выдает 0.0.0.0
Код: Выделить всё
Listening on accounting *:1813
Ready to process requests.
rad_recv: Accounting-Request packet from host 193.169.81.51:41373, id=0, length= 45
Acct-Status-Type = Accounting-On
NAS-Identifier = "Zluku"
Acct-Delay-Time = 0
NAS-IP-Address = 193.169.80.51
Processing the preacct section of radiusd.conf
modcall: entering group preacct for request 0
modcall[preacct]: module "preprocess" returns noop for request 0
rlm_acct_unique: WARNING: Attribute NAS-Port was not found in request, unique ID MAY be inconsistent
rlm_acct_unique: WARNING: Attribute Acct-Session-Id was not found in request, un ique ID MAY be inconsistent
rlm_acct_unique: WARNING: Attribute User-Name was not found in request, unique I D MAY be inconsistent
rlm_acct_unique: Hashing ',Client-IP-Address = 193.169.80.51,NAS-IP-Address = 19 3.169.81.51,,'
rlm_acct_unique: Acct-Unique-Session-ID = "ca3aaafcee5c04e5".
modcall[preacct]: module "acct_unique" returns ok for request 0
rlm_realm: Proxy reply, or no User-Name. Ignoring.
modcall[preacct]: module "suffix" returns noop for request 0
modcall[preacct]: module "files" returns noop for request 0
modcall: leaving group preacct (returns ok) for request 0
Processing the accounting section of radiusd.conf
modcall: entering group accounting for request 0
radius_xlat: '/usr/lograd/radacct/193.169.81.51/detail-20120618'
rlm_detail: /usr/lograd/radacct/%{Client-IP-Address}/detail-%Y%m%d expands to /u sr/lograd/radacct/193.169.81.51/detail-20120618
modcall[accounting]: module "detail" returns ok for request 0
modcall[accounting]: module "unix" returns noop for request 0
radius_xlat: '/usr/lograd/radutmp'
rlm_radutmp: NAS xeonchuk2 restarted (Accounting-On packet seen)
modcall[accounting]: module "radutmp" returns ok for request 0
modcall: leaving group accounting (returns ok) for request 0
Sending Accounting-Response of id 0 to 193.169.81.51 port 41373
Finished request 0
Going to the next request
--- Walking the entire request list ---
Waking up in 3 seconds...
rad_recv: Accounting-Request packet from host 193.169.81.51:59826, id=1, length= 181
Service-Type = Framed-User
Framed-Protocol = PPP
NAS-Port = 32420
NAS-Port-Type = Ethernet
User-Name = "zl8_7"
Calling-Station-Id = "18:03:73:60:CD:C4"
Called-Station-Id = "zluk8"
NAS-Port-Id = "vlan300"
Acct-Session-Id = "81e07d83"
Framed-IP-Address = 192.169.192.100
Acct-Authentic = RADIUS
Event-Timestamp = "Jun 19 2012 00:24:14 EEST"
Acct-Session-Time = 25200
Acct-Input-Octets = 443773326
Acct-Input-Gigawords = 0
Acct-Input-Packets = 950007
Acct-Output-Octets = 1829859949
Acct-Output-Gigawords = 0
Acct-Output-Packets = 1482847
Acct-Status-Type = Interim-Update
NAS-Identifier = "Zluku"
Acct-Delay-Time = 0
NAS-IP-Address = 193.169.81.51
Processing the preacct section of radiusd.conf
modcall: entering group preacct for request 1
modcall[preacct]: module "preprocess" returns noop for request 1
rlm_acct_unique: Hashing 'NAS-Port = 32420,Client-IP-Address = 193.169.81.51,NAS -IP-Address = 193.169.81.51,Acct-Session-Id = "81e07d83",User-Name = "zl8_7"'
rlm_acct_unique: Acct-Unique-Session-ID = "37fad8f400615f29".
modcall[preacct]: module "acct_unique" returns ok for request 1
rlm_realm: No '@' in User-Name = "zl8_7", looking up realm NULL
rlm_realm: No such realm "NULL"
modcall[preacct]: module "suffix" returns noop for request 1
acct_users: Matched entry DEFAULT at line 12
modcall[preacct]: module "files" returns ok for request 1
modcall: leaving group preacct (returns ok) for request 1
Processing the accounting section of radiusd.conf
modcall: entering group accounting for request 1
radius_xlat: '/usr/lograd/radacct/193.169.81.51/detail-20120618'
rlm_detail: /usr/lograd/radacct/%{Client-IP-Address}/detail-%Y%m%d expands to /u sr/lograd/radacct/193.169.81.51/detail-20120618
Последний раз редактировалось nick_S99 Вт июн 26, 2012 4:16 pm, всего редактировалось 1 раз.
-
- Site Admin
- Сообщения: 5746
- Зарегистрирован: Пт янв 28, 2005 3:11 pm
- Контактная информация:
Re: после обновления клиенту выдает 0.0.0.0
видны проблемы в настройке так как запросы обрабатываются а результат не отправляется скорее всего радиус определённые пары не понимает
modcall[preacct]: module "preprocess" returns noop for request 0
rlm_acct_unique: WARNING: Attribute NAS-Port was not found in request, unique ID MAY be inconsistent
rlm_acct_unique: WARNING: Attribute Acct-Session-Id was not found in request, un ique ID MAY be inconsistent
rlm_acct_unique: WARNING: Attribute User-Name was not found in request, unique I D MAY be inconsistent
rlm_acct_unique: Hashing ',Client-IP-Address = 193.169.80.51,NAS-IP-Address = 19
modcall[preacct]: module "preprocess" returns noop for request 0
rlm_acct_unique: WARNING: Attribute NAS-Port was not found in request, unique ID MAY be inconsistent
rlm_acct_unique: WARNING: Attribute Acct-Session-Id was not found in request, un ique ID MAY be inconsistent
rlm_acct_unique: WARNING: Attribute User-Name was not found in request, unique I D MAY be inconsistent
rlm_acct_unique: Hashing ',Client-IP-Address = 193.169.80.51,NAS-IP-Address = 19
Re: после обновления клиенту выдает 0.0.0.0
что это могут быть за проблемы?
конфиг радиуса не менялся, просто сделали обновление abills'a до последней CURRENT версии
конфиг радиуса не менялся, просто сделали обновление abills'a до последней CURRENT версии
-
- Site Admin
- Сообщения: 5746
- Зарегистрирован: Пт янв 28, 2005 3:11 pm
- Контактная информация:
Re: после обновления клиенту выдает 0.0.0.0
не понимает радиус параметры но сам ип он выдаёт хорошо это видно с дебага
Re: после обновления клиенту выдает 0.0.0.0
о каких параметрах идет речь? с какого файла??